TSC Auto ID Printers
Active IP Address
View the current IP address in use.
EAP Mode
Check the current EAP authentication mode.
My Favorite Menu Lock
Lock access to the "My Favorite" menu settings.
Ribbon Low Warning
Set the threshold at which ribbon low warnings are triggered.
Active Interface
View the active network interface.
Ethernet Version
View the current Ethernet firmware version.
NTP Server
Set the NTP server address for time sync.
Ribbon Percent
Check the percentage of ribbon used.
ASCII Data Port Set
Check the configured port for ASCII data communication.
Flash Size
View the total available flash memory.
NTP Timezone
Set the timezone used for NTP synchronization.
Save Config
Set the device to save the current configuration.
Black Line Size
Set the size of the black mark line.
FTP Set
Set the FTP service status (enabled or disabled).
Offset
Set the offset for label printing.
Security Mode
Select the WiFi security mode (e.g., WPA, WPA2).
Bline Intension
Adjust sensitivity for black line detection.
Fully Qualified Domain Name
Check the device's fully qualified domain name.
Paper/Label Length
Set the length of the labels used.
Serial Number
View the unique serial number of the device.
Bluetooth Connect Name
Set the Bluetooth connection name.
Gap Intension
Adjust sensitivity for gap detection.
Paper/Label Width
Set the width of the labels used.
Set Config
Set the device configuration from a preset.
Bluetooth Installed
Check if the Bluetooth module is present.
Gap Mark Sensor
Set the configuration for the gap or mark sensor.
Paper Low Percent
Set the percentage threshold for paper low warning.
Shift X
Adjust horizontal print alignment.
Bluetooth Mode
Set the Bluetooth operating mode (e.g., discoverable, hidden).
Gap Size
Set the size of the media gap.
Peeler Installed
Check if the peeler module is present.
Shift Y
Adjust vertical print alignment.
Boot Part Number
View the bootloader part number.
Gateway Address Set
View the assigned gateway address.
PPING Set
Set the ping response status (enabled or disabled).
SNMP Set
Set the SNMP service status (enabled or disabled).
Code Page
Set the character code page.
Head Life
View the remaining life of the print head.
Power Up Config
Check the configuration applied at startup.
SSID
Set the SSID for WiFi connection.
Company Name
View the name of the printer manufacturer.
Host Name
View or configure the host name of the printer.
Power Up State
Check the power-up behavior of the device.
Telnet Set
Set the Telnet service status (enabled or disabled).
Continuous Intension
Adjust sensitivity for continuous media.
Head On Time
Check the total active time of the print head.
Preferred Network
Select the preferred network connection type.
Tenant ID
Set the Tenant ID to associate the device with SureMDM.
Country
Set the country code for localization.
Head Print Distance
Check the total distance printed using the print head.
Print Direction
Set the print direction (normal or reverse).
Threshold Detect
Adjust the threshold for media detection.
Cutter Installed
Check if the cutter hardware is installed.
Head Resolution
Check the resolution of the printer head.
Print Intensity
Set the darkness level of printed labels.
Time
View or set the system time.
Date
View or set the system date.
HTTP Set
Set the HTTP configuration settings.
Print Mode
Set the current print mode (e.g., continuous, batch).
Time Format
Set the format for displaying the time.
Date Format
Set the format for displaying the date.
Label Rotation
Set the label orientation (portrait or landscape).
Printer On Time
Check how long the printer has been powered on.
Total Label Count
View the total number of labels printed.
DC Part Number
View the DC part number of the device.
LCD Brightness
Adjust the brightness of the LCD screen.
Print Server Name
View the name assigned to the print server.
Total Media Distance
View the total media distance printed.
DHCP Set
Set the DHCP mode (enabled or disabled).
Maximum Gap Mark
Set the maximum gap or black mark size.
Print Speed
Set the speed at which the device prints.
TPH Care Enable
Enable print head (TPH) care monitoring.
Display LAN
View the current LAN interface in use.
Media Sensor
Set the type of media sensor to be used.
Program File
Check the current firmware file version.
Unhealthy Dot Threshold
Set the threshold for identifying unhealthy print head dots.
Display Language
Set the display language of the printer interface.
Media Units
View the units used for measuring media (e.g., inches or mm).
QCMC Installed
Check if the QCMC module is present.
WEP Key Index
Set the WEP key index for WiFi authentication.
Display Line 1
Set the first line of display text shown on the device screen.
Menu Lock
Set whether the on-device menu should be locked or unlocked.
Reference X
Set the X-axis reference point for printing.
WiFi DHCP
Enable or disable DHCP for WiFi connections.
Display Line 2
Set the second line of display text shown on the device screen.
Minimum Paper
Set the minimum acceptable paper length.
Reference Y
Set the Y-axis reference point for printing.
WLAN Installed
Check if the WLAN module is available.
DRAM Size
View the total installed DRAM memory.
Model
View the model name of your TSC Auto ID device.
RFID Installed
Check if the RFID module is installed.